Updated November 2026
To bleed a solar hot water system, you release the air trapped in the collector loop through a bleed or air vent valve, then refill the loop until only fluid comes out. Done correctly, this restores circulation, stops gurgling and banging in the pipes, and lets the pump move heat from the collectors to your storage tank. The job takes under an hour on most rooftop systems, but it needs to be done with the pump off and the system cool.
Why Air Gets Into the Loop
Closed-loop systems circulate a glycol-water mix through the collectors and a heat exchanger. Air gets in during the initial fill, through small leaks at fittings, or when the fluid level drops and the pump draws air through a suction side. Trapped air forms pockets in the high points of the collector array, blocking flow. The result is often a collector that stays cold while the rest of the loop is warm, or a pump that runs hot and noisy. Consult the manufacturer’s manual before opening any valve, since pressure and temperature limits vary by model.
Shopping for one? See our guide: Air in Solar Hot Water System: 7 Best Air Vent and Bleed Valves Compared (2026).
How to Bleed a Solar Hot Water System Step by Step
Work in the early morning or on an overcast day so the collectors are not hot enough to flash the fluid into steam. Keep the pump switched off and the controller in manual or standby mode.
- Check the system pressure gauge on the solar loop. Most closed-loop systems run between about 12 and 30 psi when cold; note the reading before you start.
- Locate the air vent or bleed valve at the highest point of the collector array and at any manual bleed fitting near the pump or heat exchanger.
- Place a container under the bleed valve and a hose on the drain valve if your system has one.
- Open the bleed valve slowly. Listen for hissing, then watch for fluid. Close the valve when a steady stream of fluid appears with no air.
- If the pressure drops below the recommended range, open the fill valve and top up with the manufacturer-specified heat transfer fluid until the gauge reads correctly.
- Switch the pump on in manual mode and run it for five to ten minutes. Watch the gauge and listen for gurgling.
- Repeat the bleed at the high point and any other vents until the flow is smooth and the pressure holds steady.
- Return the controller to automatic mode and confirm the collectors warm up when the sun is on them.
Checking the Fluid Level
After bleeding, the expansion tank should sit at its normal level and the gauge should hold. A pressure that keeps falling points to a leak rather than trapped air, and that needs its own repair.
Factors That Affect the Bleed
| Factor | What to Check |
|---|---|
| Collector temperature | Bleed only when collectors are cool |
| System pressure | Confirm the gauge reads within the manufacturer’s range |
| Number of high points | Each collector row may need its own vent |
| Fluid type | Use only the heat transfer fluid the manufacturer specifies |
Common Mistakes
- Bleeding a hot system, which can scald you and flash the fluid.
- Opening the valve fully at once, which can release fluid too fast.
- Mixing fluid types or topping up with plain water.
- Skipping the pressure check, so the loop runs low and the air returns.
- Ignoring a pressure drop that repeats, which usually signals a leak to trace.
Recommended gear
A clear drain hose makes it easy to watch for air bubbles as fluid runs out of the valve. View on Amazon
A small catch container keeps glycol off the roof and out of gutters. View on Amazon
A pressure gauge with a clear dial helps you confirm the system returns to its cold range after bleeding. View on Amazon
FAQ
How often should I bleed my solar hot water system?
Most owners only need to bleed after a service visit, a fluid top-up, or when gurgling appears. Frequent air returns usually mean a leak or a fitting that is drawing air in.
Can I bleed the system myself?
Many homeowners can handle a simple bleed at an accessible vent. Because the roof work and hot fluid carry real risk, consult a qualified solar installer if the vent is hard to reach or the pressure problem persists.
Why is my collector still cold after bleeding?
Air may remain in a higher section, the pump may not be running, or the controller may be set incorrectly. Recheck each vent and confirm the pump runs when the collectors are warmer than the tank.
Conclusion
Bleeding a solar hot water system removes trapped air, restores flow, and lets the collectors heat your water again. Work only on a cool system, check pressure before and after, and use only the fluid the manufacturer specifies. If air keeps returning, look for a leak before you bleed again.
Related reading
- Solar Hot Water System With Gas Booster: How to Set One Up Step by Step
- Solar Hot Water System With Gas Backup: How to Set It Up Right
- Solar Hot Water System Suppliers: How to Choose the Right One (2026)
- Solar Hot Water System Size Calculator: How to Size Your System Right
- Solar Hot Water System Rebate: How to Find and Claim Yours (2026)
