Updated November 2026
A solar hot water heater thermosiphon uses the natural rise of warm water to move heat from a collector on the roof into a storage tank, with no pump or controller involved. This guide walks through the layout, the key measurements, and the install details that decide whether the loop actually circulates. By the end you will know what to buy, how to position the parts, and how to test the system before you insulate it.
How a Thermosiphon Loop Works
Warm water is less dense than cold water, so it rises. In a thermosiphon system, water heated in the collector rises out the top and flows into the tank, while cooler water settles out of the bottom of the tank and drops back into the collector. This cycle continues as long as the collector is hotter than the water in the tank. For a deeper explanation of the physics, see Thermosiphon Solar Water Heaters: Natural Circulation Explained.
Shopping for one? See our guide: Top 5 Solar Hot Water Heater Evacuated Tube Collector Options Compared.
Because flow depends on density differences rather than pressure, every design choice comes down to keeping that flow path open and unobstructed.
Plan the Layout and Height Difference
The tank must sit above the top of the collector. Most builders aim for the bottom of the tank to be at least 12 to 18 inches above the collector outlet, though the exact figure depends on pipe length and diameter. A longer, narrower run creates more resistance, so keep the pipe run short and use at least 3/4-inch copper or PEX for the loop.
- Mount the collector facing true south in the Northern Hemisphere, tilted near your latitude.
- Run the hot outlet from the top of the collector to the top of the tank with a continuous upward slope.
- Run the cold return from the bottom of the tank to the bottom of the collector with a continuous downward slope.
- Avoid horizontal runs longer than necessary and avoid any low loops that can trap air.
Assemble the Collector, Tank and Piping
Connect the collector and tank using the layout you planned. Use isolation valves at both ends so you can service the tank without draining the collector. Install a temperature and pressure relief valve on the tank, rated for your system pressure, and route its discharge to a safe drain.
Step-by-step assembly
- Mount the tank on a frame rated for its filled weight, with the cold inlet at the bottom and the hot outlet at the top.
- Mount the collector on the roof or a rack, securing it against wind uplift.
- Connect the hot riser and cold return, keeping slopes continuous.
- Install isolation valves, a check valve on the cold line, and a drain valve at the lowest point.
- Insulate all exposed piping with closed-cell foam rated for solar temperatures.
Test Circulation Before You Finish
Fill the system and open the valves. On a sunny day, the collector should feel noticeably warmer than the tank within an hour, and you should see the hot outlet pipe warm up before the tank does. If the riser stays cool, check for trapped air, a flat section in the pipe, or a restriction at a fitting. Owners often report that a small air pocket at the top of the collector is the most common cause of no flow.
Recommended gear
A flow meter and temperature probes help you confirm the loop is moving water rather than guessing from pipe temperature alone.
- Digital thermometer probes for the collector outlet and tank bottom: View on Amazon
- Closed-cell pipe insulation sized to your line diameter: View on Amazon
- Brass isolation ball valves for the loop: View on Amazon
Common mistakes
- Placing the tank at roof level or below the collector, which stops natural flow.
- Using undersized pipe that creates too much resistance for a thermosiphon loop.
- Leaving low points in the riser where air collects.
- Skipping a pressure relief valve on the tank.
- Forgetting that scale builds up over time, so check the water source before you commit to this design. See Water Quality and Scaling in Solar Water Heaters.
FAQ
Does a thermosiphon system need electricity?
No. Circulation comes from temperature-driven density differences, so the system runs without a pump. Some builders add a small backup heater, which does require power.
How high does the tank need to be above the collector?
Many builders aim for at least 12 to 18 inches between the collector outlet and the bottom of the tank, but the right height depends on pipe run and diameter. Test flow after installation and adjust if needed.
Can I use a thermosiphon system in freezing weather?
Only with freeze protection, such as drain-back design or antifreeze loops. Consult a qualified professional or your local code official before installing in a cold climate.
Conclusion
A solar hot water heater thermosiphon works by letting heated water rise naturally into the tank, so the layout and pipe sizing matter more than any control hardware. Set the tank above the collector, keep slopes continuous, and test for flow before insulating. With those steps done, the loop should run reliably on sunny days.
