Updated November 2026

A solar hot water system leaking from release valve is usually a sign of excess pressure, a failing valve, or a problem with the expansion tank. In most cases you can narrow down the cause in under an hour by checking pressure, temperature and the valve itself. This guide walks you through the checks, the fixes and the situations where you should stop and call a licensed plumber.

First, Confirm It Is the Release Valve

Before you touch anything, make sure the water is actually coming from the pressure relief or temperature and pressure (T&P) valve and not from a joint, a tank fitting or a pipe. Dry the area with a towel, wait, and watch where the drip begins. Water collecting around the discharge pipe, or a steady drip from the valve’s outlet, points to the valve. Dampness on a pipe joint or the tank shell points elsewhere. For roof-mounted collectors, the same logic applies; see Solar Hot Water System Leaking on Roof: How to Find and Fix It if the drip seems to start up high.

Shopping for one? See our guide: 4 Best Pressure Relief Valve Solar Hot Water System Options Compared (2026).

Check the Cause: Pressure, Heat or Valve Failure

A release valve opens for one of three reasons. Knowing which one applies tells you what to fix.

  • Excess pressure. Water expands as it heats. If the expansion tank is waterlogged or undersized, pressure climbs until the valve lifts.
  • Excess temperature. Stagnation on a sunny day, or a faulty thermostat or controller, can push tank temperature past the valve’s set point.
  • A worn or debris-fouled valve. Sediment, mineral scale or a weak spring can cause a seep even when pressure is normal.

Use a pressure gauge on the cold supply side and read it at a quiet time of day. Manufacturers generally specify a working pressure in the range that your valve and tank are rated for, and anything consistently above that rating is a problem to solve, not a reading to ignore.

Step-by-Step Fix

  1. Turn off the cold water supply to the heater and let the system cool if it is hot. Do not touch the valve lever while the water is hot.
  2. Check the expansion tank. Tap it: a solid thump means it is waterlogged. Drain it, check the air charge with a tire gauge, and set it to match your system’s cold-fill pressure.
  3. Look at the pressure reading. If it runs high even with a good expansion tank, the pressure-reducing valve on the cold line may be failing. Replace it.
  4. Check the temperature setting and controller. If the tank runs hot, have the thermostat or differential controller inspected.
  5. Test the release valve by lifting its test lever briefly. Water should flow freely, and the valve should reseat fully when released. If it keeps dripping after reseating, flush it with the lever a few times, and if it still seeps, replace it with a valve of the same rating.
  6. Restore the supply, refill slowly, and watch the valve for an hour or two after the system heats up.

Checklist of Tools and Supplies

  • Towel or bucket and a flashlight
  • Pressure gauge with a hose or tap fitting
  • Tire gauge for checking the expansion tank air charge
  • Replacement T&P or pressure relief valve matching the original rating
  • Pipe wrench, PTFE thread tape and a short length of discharge pipe

Quick Reference: Symptom and Likely Cause

What you see Most likely cause First action
Drip only on hot, sunny days Excess temperature or stagnation Check controller and thermostat
Constant seep, tank thumps when tapped Waterlogged expansion tank Drain and recharge expansion tank
Gauge reads high at all times Failing pressure-reducing valve Replace pressure-reducing valve
Drips after lever test, pressure normal Debris or worn valve seat Flush, then replace valve

Common Mistakes to Avoid

  • Plugging or capping the valve outlet. The valve is a safety device and must always discharge freely.
  • Replacing the valve without fixing the cause. A new valve will leak again if pressure is still high.
  • Using a valve with a higher pressure or temperature rating than the tank allows.
  • Routing the discharge pipe upward or sealing its end. It should drop to a safe drain location with a continuous downward slope.
  • Ignoring a valve that keeps weeping. Low-level seeping still signals an issue to track down.
  • Digital pressure gauge with a hose fitting. It lets you read system pressure at the tap and compare it over several days.
    View on Amazon
  • Tire pressure gauge with a low-range scale. Expansion tank charges are set at low pressure, and a standard car gauge is often too coarse.
    View on Amazon
  • PTFE thread seal tape. It seals the replacement valve threads without leaving a residue that can jam the seat.
    View on Amazon

FAQ

Is a leaking release valve dangerous?

It can be. The valve protects the tank from over-pressure and over-temperature, so a fault may mean the system is operating outside its safe limits. Treat repeated discharge as a serious warning and fix it promptly.

Can I replace the release valve myself?

Many homeowners with basic plumbing skills can swap a valve, but the work involves hot water, pressure and possibly roof access. If you are unsure, consult a licensed plumber or solar installer.

Why does the valve only leak in summer?

Solar collectors reach their highest temperatures on hot, clear days, so pressure and temperature peak then. A leak that appears only in summer usually points to the expansion tank, the controller or stagnation rather than the valve itself.

Conclusion

A solar hot water system leaking from release valve is almost always traceable to pressure, temperature or a worn valve. Work through the checks in order, confirm the cause, and then fix that cause rather than just replacing the valve. If the leak continues after these steps, or you are uncomfortable working with pressurized hot water, consult a licensed professional.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our solar water heaters guides, checking product details against manufacturer specifications and owner feedback.