Updated November 2026

A solar water heater electric coil is a resistance heating element that sits inside the storage tank and heats water when the sun cannot keep up, such as on cloudy days or in winter. This guide explains how the coil works, how to choose one, and how to wire and install it safely. You will end up with a backup system that keeps hot water available without relying on the sun alone.

How a Solar Water Heater Electric Coil Works

The coil is a metal element, usually copper or incoloy-sheathed, that converts electrical current into heat through resistance. When it is energized, it heats the water surrounding it, and a thermostat cuts power once the tank reaches its set point. Most DIY builds place the coil in the upper third of the tank, because hot water rises and the thermostat then reads the warmest zone.

Shopping for one? See our guide: 5 Best Solar Batch Water Heaters for Homeowners (2026).

Coils are usually rated in watts. Manufacturers commonly specify 1,500 to 4,500 watts for residential tanks, and higher ratings heat faster but draw more current. Check that your circuit and breaker can handle the rating before you commit to a size.

Choosing the Right Coil for Your Tank

Match the coil to your tank volume and your electrical service. A 40-gallon tank needs less element power than a 120-gallon tank to reach the same temperature in a reasonable time. Confirm the threaded connection size matches your tank port, and make sure the element length fits inside the tank without touching the bottom.

  • Tank volume and desired recovery time
  • Available circuit amperage and breaker size
  • Element material suited to your water (see the scaling note below)
  • Thermostat type: built-in or external

Step-by-Step Installation

Work with the power off at the breaker and confirm the circuit is dead with a voltage tester before touching any wiring. Installation steps are below.

  1. Drain the tank below the coil port, and close the cold inlet valve.
  2. Clean the threads and apply the thread sealant or Teflon tape recommended by the coil manufacturer.
  3. Insert the element through the port, keeping the gasket seated flat, and tighten to the torque the manufacturer specifies.
  4. Mount the thermostat on the tank wall at the height the instructions give, normally near the upper third.
  5. Run a dedicated circuit with wire gauge matched to the breaker, and bond the tank to ground.
  6. Refill the tank, check every fitting for leaks, then restore power and set the thermostat.

Electrical work carries real shock and fire risk. If you are not confident wiring a dedicated circuit, consult a licensed electrician before energizing the element.

Common Mistakes to Avoid

  • Energizing the coil with the tank empty, which burns out the element quickly.
  • Undersizing the wire or breaker for the element wattage.
  • Skipping the ground bond to the tank.
  • Ignoring water hardness, since scale builds up on the element and reduces heat transfer.
  • Setting the thermostat too high, which raises scalding risk at the tap.

A non-contact voltage tester helps confirm the circuit is dead before you start. View on Amazon

Pipe thread sealant rated for potable water keeps the element port leak-free. View on Amazon

A wire stripper and crimping kit makes clean, secure connections on the element leads. View on Amazon

FAQ

Can a solar water heater electric coil run on solar power?

Yes, if your solar electric system has enough capacity to supply the element’s wattage, though most builds use grid power as backup. Battery or inverter sizing must account for the coil’s draw.

How often should I check the element for scale?

Inspect it once a year, or more often in hard-water areas. Light scale can be flushed, but heavy buildup usually calls for replacing the element.

Do I need a thermostat with the coil?

Yes. The thermostat stops the element once the water reaches its set point, which protects the tank and prevents scalding.

Conclusion

A solar water heater electric coil gives your system a dependable backup, so hot water stays available through cloudy stretches and cold months. Size the element to your tank, install it with the power off, and check it yearly for scale. Following these steps will get your build running safely and reliably.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our solar water heaters guides, checking product details against manufacturer specifications and owner feedback.