Updated November 2026
A tankless water heater solar system uses a solar collector to pre-heat water, then a tankless unit fires up only when that water needs an extra boost. This guide explains how the two pieces work together, what components you need, and the factors that decide whether the setup suits your home. You will finish with a clear plan for sizing and connecting the parts.
How a Solar Tankless Setup Works
In a solar tankless water heater setup, the solar collector does most of the heating. Water passes through the collector and into a storage tank or straight to a point where a tankless unit sits downstream. The tankless unit reads the outlet temperature and adds heat only when the solar-warmed water falls short of your set point. Because a tankless unit has no stored volume to keep hot, it works best as a backup rather than as the main heat source.
Shopping for one? See our guide: 5 Best Solar Batch Water Heaters for Homeowners (2026).
Some people call this a solar water heater with tankless backup, a tankless solar water heater, or a solar water heater tankless hybrid. The name varies, but the layout is the same: solar first, tankless second.
Choosing Your Components
Start with the collector type, since it sets how much usable heat you get in cold weather. Flat plate collectors suit mild climates, while evacuated tube collectors hold heat better in winter. Check the manufacturer’s rated output and match it to your daily hot water use. Our guide to Solar Water Heater Collectors: Batch, Flat Plate and Evacuated Tube compares the options in more detail.
Next, pick the tankless unit. Look for one rated for your flow rate in gallons per minute and your required temperature rise. Confirm that the unit accepts a low-temperature inlet, because solar-preheated water often arrives warm enough to reduce the load significantly.
Finally, plan the controls. A differential controller with a pump, collector sensor and tank sensor keeps the system from running the pump when there is no useful heat to gain. You can read more in Solar Water Heater Controls and Sensors: How Differential Control Works.
Installing the Solar Tankless Loop
Installation follows the same logic as any solar loop, with the tankless unit added at the end. Work through these steps in order:
- Mount the collector facing south in the Northern Hemisphere, tilted near your latitude.
- Run insulated supply and return lines to the storage point, keeping runs short.
- Install the circulation pump, check valve and expansion tank on the cold side of the loop.
- Place the tankless unit after the solar storage, with its cold inlet fed from the preheated line.
- Mount the sensors, wire the controller, and fill and purge the loop before powering anything on.
- Test the outlet temperature at a faucet and adjust the tankless set point to match.
Manufacturers specify minimum clearances, pressure ratings and venting requirements for their tankless units, so follow the installation manual exactly. Many jurisdictions require a permit and inspection for gas or electric tankless equipment.
Sizing for Your Household
Estimate daily hot water use by adding up fixture flow rates and typical run times. A household with two bathrooms, a dishwasher and a washing machine will need a larger collector area and a higher-flow tankless unit than a single-occupant apartment. Use the flow rate of your tankless unit as the limit on simultaneous use, not as a daily total.
| Factor | What to check |
|---|---|
| Climate | Winter sun hours and freeze risk |
| Flow rate | Peak gallons per minute at the busiest outlet |
| Roof space | Collector area, orientation and shading |
| Fuel | Gas, propane or electric backup availability |
Common Mistakes and Tips
- Sizing the tankless unit for solar temperatures alone, when the backup must also handle cloudy days.
- Skipping a check valve, which can let heated water flow backward at night.
- Using undersized pipe, which cuts flow and can starve the tankless unit.
- Ignoring scale; check the guidance in Water Quality and Scaling in Solar Water Heaters if your water is hard.
- Forgetting freeze protection in cold regions, covered in Winterizing a DIY Solar Water Heater: Freeze Protection Options.
Recommended Gear
- A differential temperature controller helps the pump run only when the collector is hotter than the storage point. View on Amazon
- Pipe insulation reduces heat loss on the run between collector and tankless unit. View on Amazon
- A pressure relief valve protects the loop from overpressure during stagnation. View on Amazon
FAQ
Can a tankless water heater run on solar alone?
Usually not. Solar supplies most of the heat in good weather, but cloudy days and winter months typically need a backup heat source to reach a safe, usable temperature.
Do I need a permit for a solar tankless setup?
Often yes, especially where gas or electric tankless equipment is involved. Check with your local building department and consult a licensed professional before work begins.
How do I know the right size for my home?
Start with your daily hot water use and peak flow rate, then compare them to the collector and tankless ratings. A qualified installer can confirm the sizing against your local climate.
Conclusion
A tankless water heater solar system pairs a solar collector with an on-demand backup, giving you preheated water and a reliable top-up. Size the collector for your climate and flow needs, follow the manufacturer’s installation steps, and add proper controls and freeze protection. For gas, electric or structural work, consult a licensed professional.
Related reading
- Winterizing a DIY Solar Water Heater: Freeze Protection Options
- Water Quality and Scaling in Solar Water Heaters
- Top 7 Solar Thermal Temperature Sensors Compared for Solar Water Heaters
- Top 5 Thermal Solar Water Heater Options Compared in 2026
- Top 5 Solar Thermal Water Heater System Options Compared for Homes
