Updated November 2026

A solar electric water heater system uses photovoltaic panels to power an electric element inside a storage tank, so you can heat water without burning fuel. In this guide you will learn how the system works, how to size the panels and tank, and how to wire in an electric backup so you always have hot water. The steps below assume you already have basic electrical skills and a clear idea of your household hot water demand.

How a Solar Electric Water Heater System Works

Unlike a solar thermal system, which circulates heated fluid through a collector, a solar electric setup converts sunlight to electricity and sends that power to a resistance element. The element heats the water directly in the tank. Because the energy path is electrical, you can route wiring, controls and backup power with the same tools you would use on any 12V or 240V circuit. The tradeoff is that PV panels and an element are less efficient per square foot than a well-designed flat-plate collector, so you will need more roof area for the same output.

Shopping for one? See our guide: 6 Best Books to Build a Solar Hot Water Heater Systems (2026).

Sizing the Panels, Tank and Element

Start by estimating daily hot water use. A common planning figure is around 20 gallons per person per day, though your habits will vary. Then work out the energy needed to raise that volume by the temperature rise you want. Water needs roughly 8.34 BTU per gallon per degree Fahrenheit, which converts to about 0.00244 kWh per gallon per degree. For 60 gallons heated 70°F, that is about 10 kWh per day, before losses.

Divide the daily energy target by your local peak sun hours to estimate array wattage, then add 20 to 30 percent for losses. Element wattage should be matched to the panels so the controller can run the element during full sun without overloading the array. Check the Solar Water Heater System Installation: A Step-by-Step Guide for DIYers for layout details, and use What Size Solar Hot Water System Do I Need? A Step-by-Step Sizing Guide to cross-check your numbers.

Choosing the Storage Tank

Most DIY builds use a well-insulated tank sized to one or two days of demand. Look for a tank rated for potable water, with a built-in element port and a drain valve. Insulation thickness matters more than most builders expect, because standing losses steal heat overnight.

Wiring the Electric Backup

A solar electric system needs a backup for cloudy weeks. The usual approach is a thermostat-controlled electric booster that engages only when the tank drops below a set temperature. Install it on its own breaker, with the thermostat wired so the solar element and the backup element never run at the same time. Overlapping loads trip breakers and waste capacity.

Several commercial systems combine solar and electric boost in one package, and comparing them can clarify the wiring. See 5 Best Solar Electric Boost Hot Water System Options for Home Use (2026) and 4 Best Electric Hot Water Systems with Solar Panels Options Compared (2026) for examples of how manufacturers handle the integration.

  1. Confirm daily hot water demand and target temperature.
  2. Calculate energy needed and convert it to array wattage.
  3. Select a tank with a suitable element port and insulation.
  4. Mount panels facing south in the Northern Hemisphere, tilted near your latitude.
  5. Install the solar element and controller on a dedicated circuit.
  6. Wire the electric backup thermostat with interlocks.
  7. Test temperatures, breakers and drain valves before closing up.

Common Mistakes to Avoid

  • Undersizing the panels because you based the design on average, not peak, sun.
  • Skipping a dedicated breaker for the element, which leads to nuisance trips.
  • Neglecting freeze protection in cold climates; see Winterizing a DIY Solar Water Heater: Freeze Protection Options.
  • Ignoring water hardness, which scales elements and reduces output over time.
  • Running wiring without a licensed electrician check where local code requires it.
  • Digital temperature controller lets you set the backup threshold precisely. View on Amazon
  • Heavy-gauge outdoor PV wire handles sun exposure and voltage drop on long runs. View on Amazon
  • Immersion element thermostat provides the backup control that prevents overlapping loads. View on Amazon

FAQ

Can a solar electric water heater system work in winter?

It can, but output drops with shorter days and lower sun angles. Most builders rely on the electric backup during winter months and size the panels with that in mind.

Do I need a permit to install one?

Requirements vary by location, and electrical work usually needs a permit and inspection. Check with your local building department and consult a licensed electrician before wiring.

How long does the tank hold heat?

It depends on insulation quality and ambient temperature. A well-insulated tank loses only a few degrees overnight, while thin insulation can lose far more.

Conclusion

A solar electric water heater system is straightforward when you size it from real demand and keep the solar and backup loads separate. Work through the energy math, wire the controls carefully, and test every circuit before you rely on it. Consult a licensed professional for any work your local code requires them to handle.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our solar water heaters guides, checking product details against manufacturer specifications and owner feedback.