Updated November 2026

Solar water heater supplies fall into a few clear groups: collectors, storage, plumbing, circulation, controls and insulation. This guide walks through each group so you can build a complete parts list before buying anything. Once you have it, you can match components to your roof, your climate and the hot water demand of your household.

Step 1: Choose Your Collector Type

The collector is the largest and most expensive item on the list, so settle it first. Flat plate collectors suit most residential builds in moderate climates. Evacuated tube collectors handle cold weather and low sun better, and batch heaters are the simplest option if you want a tank that doubles as the collector. Read through Solar Water Heater Collectors: Batch, Flat Plate and Evacuated Tube for a side-by-side comparison before you commit to one design.

Shopping for one? See our guide: 5 Best Solar Batch Water Heaters for Homeowners (2026).

Step 2: Gather Storage, Plumbing and Circulation Parts

Storage and plumbing supplies determine whether the system holds pressure and moves heat efficiently. Most builds need the following:

  • An insulated storage tank sized to your daily hot water use, often in the range of 40 to 80 gallons for a small household.
  • Copper or cross-linked polyethylene (PEX) tubing rated for the temperatures your collector will reach, typically 3/4-inch for the main loop.
  • Brass or bronze fittings, unions and isolation valves so components can be serviced without draining the system.
  • A circulator pump for pumped systems, or the height difference needed for a thermosiphon loop.
  • A pressure relief valve and expansion tank rated for the system’s maximum pressure.
  • Heat-transfer fluid (propylene glycol) if you live where freezing occurs.

For how natural circulation differs from pumped flow, see Thermosiphon Solar Water Heaters: Natural Circulation Explained.

Step 3: Add Controls, Sensors and Insulation

Controls keep the pump from running when the collector is cooler than the tank, which saves energy and protects the tank from heat loss. A differential controller needs two temperature sensors, one on the collector and one at the bottom of the tank. Mount sensors with thermal paste and insulate them against ambient air.

Insulate every exposed pipe and the tank itself. Use closed-cell foam or mineral wool pipe insulation rated for outdoor use, and cover it with UV-resistant jacketing if it will see sunlight. Water quality also affects long-term performance, so review Water Quality and Scaling in Solar Water Heaters before you select fittings.

Parts Checklist

  1. Collector panels or tubes, sized to your roof area and daily demand
  2. Insulated storage tank
  3. Tubing, fittings, unions and isolation valves
  4. Circulator pump (pumped systems)
  5. Expansion tank and pressure relief valve
  6. Differential controller and two temperature sensors
  7. Propylene glycol fluid (freeze-prone climates)
  8. Pipe insulation, tank insulation and UV jacketing
  9. Mounting hardware, brackets and roof flashing

Common Mistakes to Avoid

  • Buying fittings rated only for cold water. Collector loops can exceed 180°F during stagnation.
  • Skipping the pressure relief valve or sizing it below the system’s rated pressure.
  • Undersizing the tank, which causes the system to overheat during long sunny days.
  • Leaving pipe insulation exposed to UV, which breaks it down within a few seasons.
  • Ignoring local codes. Check Solar Water Heater Codes, Permits and Professional Review before ordering parts.

A differential controller with dual sensors is the component most DIY builders underestimate. Search for solar thermal differential controller and confirm it supports your pump voltage. View on Amazon

Pipe insulation rated for outdoor and high-temperature use protects your tubing from heat loss and UV damage. View on Amazon

Propylene glycol pre-mixed for solar loops simplifies filling and reduces the risk of mixing errors. View on Amazon

FAQ

Can I use standard household plumbing parts for a solar water heater?

Standard parts often lack the temperature and pressure ratings a solar loop needs. Confirm that every fitting, valve and hose is rated for at least the maximum stagnation temperature of your collector.

How many collector panels do I need?

The answer depends on your daily hot water use, local sun hours and roof space. Many small households start from a sizing calculation based on gallons per day, and manufacturers publish collector output figures you can use for that math.

Do I need a permit to install solar water heater supplies?

Requirements vary by city, county and state, and some areas require a licensed plumber or permit for roof mounting or pressurized loops. Check with your local building department before installation, and consult a licensed professional for any work involving gas, electrical or structural changes.

Conclusion

A complete parts list covers collectors, storage, plumbing, circulation, controls and insulation. Working through the groups in order keeps you from overlooking a fitting or sensor that stops the system from working. Confirm temperature and pressure ratings on every item, and verify local code requirements before you buy.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our solar water heaters guides, checking product details against manufacturer specifications and owner feedback.